smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.10.0-33-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.12
Device Model: ST3320418AS
Serial Number: 9VM2639M
LU WWN Device Id: 5 000c50 0156e96fd
Firmware Version: HP11
User Capacity: 320,072,933,376 bytes [320 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Mon Sep 18 14:30:32 2017 IST
==> WARNING: A firmware update for this drive may be available,
see the following Seagate web pages:
http://knowledge.seagate.com/articles/en_US/FAQ/207931en
http://knowledge.seagate.com/articles/en_US/FAQ/213891en
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 625) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 74) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 105 099 006 Pre-fail Always - 9405733
3 Spin_Up_Time 0x0023 098 097 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 096 096 020 Old_age Always - 4356
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x002f 061 054 030 Pre-fail Always - 1271704818194
9 Power_On_Hours 0x0032 085 085 000 Old_age Always - 13695
10 Spin_Retry_Count 0x0033 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 096 096 020 Old_age Always - 4358
184 End-to-End_Error 0x0033 100 100 097 Pre-fail Always - 0
187 Reported_Uncorrect 0x0032 094 094 000 Old_age Always - 6
188 Command_Timeout 0x0032 100 098 000 Old_age Always - 190
189 High_Fly_Writes 0x003a 099 099 000 Old_age Always - 1
190 Airflow_Temperature_Cel 0x0022 070 056 045 Old_age Always - 30 (Min/Max 30/31)
194 Temperature_Celsius 0x0022 030 044 000 Old_age Always - 30 (0 21 0 0 0)
195 Hardware_ECC_Recovered 0x003a 047 042 000 Old_age Always - 9405733
196 Reallocated_Event_Count 0x0032 100 100 036 Old_age Always - 0
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 2
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 6 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 6 occurred at disk power-on lifetime: 12941 hours (539 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 03:40:51.264 READ DMA EXT
25 00 08 ff ff ff ef 00 03:40:51.262 READ DMA EXT
25 00 08 ff ff ff ef 00 03:40:51.262 READ DMA EXT
25 00 08 ff ff ff ef 00 03:40:51.262 READ DMA EXT
25 00 08 ff ff ff ef 00 03:40:51.261 READ DMA EXT
Error 5 occurred at disk power-on lifetime: 12941 hours (539 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 ff ff ff ef 00 03:40:48.367 READ DMA EXT
25 00 00 ff ff ff ef 00 03:40:48.365 READ DMA EXT
25 00 00 ff ff ff ef 00 03:40:48.363 READ DMA EXT
25 00 00 ff ff ff ef 00 03:40:48.362 READ DMA EXT
25 00 00 ff ff ff ef 00 03:40:48.361 READ DMA EXT
Error 4 occurred at disk power-on lifetime: 12941 hours (539 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 03:36:27.301 READ DMA EXT
25 00 08 ff ff ff ef 00 03:36:27.301 READ DMA EXT
25 00 08 ff ff ff ef 00 03:36:27.301 READ DMA EXT
25 00 08 ff ff ff ef 00 03:36:27.301 READ DMA EXT
25 00 08 ff ff ff ef 00 03:36:27.300 READ DMA EXT
Error 3 occurred at disk power-on lifetime: 12941 hours (539 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 ff ff ff ef 00 03:36:24.113 READ DMA EXT
25 00 00 ff ff ff ef 00 03:36:24.054 READ DMA EXT
25 00 00 ff ff ff ef 00 03:36:24.054 READ DMA EXT
25 00 00 ff ff ff ef 00 03:36:24.052 READ DMA EXT
25 00 00 ff ff ff ef 00 03:36:24.051 READ DMA EXT
Error 2 occurred at disk power-on lifetime: 12941 hours (539 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 03:06:21.100 READ DMA EXT
25 00 08 ff ff ff ef 00 03:06:21.099 READ DMA EXT
25 00 08 ff ff ff ef 00 03:06:21.099 READ DMA EXT
25 00 08 ff ff ff ef 00 03:06:21.098 READ DMA EXT
25 00 08 ff ff ff ef 00 03:06:21.098 READ DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 13695 -
# 2 Extended offline Interrupted (host reset) 70% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.